The 8 Wastes of Lean (TIMWOODS)
In Lean, waste (the Japanese term is muda) is any activity that consumes time, material, or attention but does not add value the customer is willing to pay for. The eight wastes, often remembered with the acronym TIMWOODS, are Transportation, Inventory, Motion, Waiting, Overproduction, Overprocessing, Defects, and Skills (unused talent).
The original Toyota list had seven wastes; unused skills were added later as the eighth.
Value-added, required, and pure waste
Not every non-value-added step can disappear tomorrow. A useful three-way split is:
- Value-added: the customer cares about the change, and it is done right the first time — machining a hinge leaf to print, or assembling the pin so the door can swing.
- Required non-value-added (necessary waste): the customer would not pay extra for it, but you must do it today because of regulation, a current layout, or a technology limit — a required material cert, or a move between buildings you do not yet own a way to avoid.
- Pure waste: it can be removed without harming the customer or a legal requirement — a double inspection that never finds a unique defect, or a weekly report nobody reads.
Lean work starts by seeing all three, then attacking pure waste first and redesigning the process so less “required” waste is actually required.
The eight wastes, with examples
The examples below come from the same fictional plant used across this Body of Knowledge, Northriver Hardware, which makes residential door hinges.
Transportation
Moving materials, paperwork, or files farther or more often than the work requires. A move does not change the product. At Northriver, finished hinges traveled to a remote staging cage and back to the dock, adding a day and two forklift touches. Transportation waste often hides behind a bad layout or a “that is where the rack has always been” habit.
Inventory
Raw material, work in process, finished goods, or digital queues beyond what is needed to serve the customer now. Inventory hides other wastes: if there are three days of leaves in front of assembly, a dull tool or a bad pin lot is not felt until much later. See also work in progress (WIP). A Kanban or other pull system is one way to cap that inventory on purpose.
Motion
Unnecessary movement of people: reaching, walking, digging through a drawer, or clicking through six screens to enter one result. Motion is usually a 5S and workplace-design problem. At Northriver, assemblers walked 40 feet each cycle for the boxed pins because the vendor pack was left on a pallet “to save a setup.”
Waiting
Idle time for a person, a machine, a part, a signature, or a system response. Waiting is often the largest bar on a value stream timeline. Northriver’s CNC cell waited on first-piece approval because the inspector covered three lines and was called only after a tray was already full.
Overproduction
Making more, earlier, or faster than the next process or the customer needs. Overproduction is often called the most serious waste because it creates inventory, transportation, and hidden defects. “The machine is paid for, so keep it running” is a common trigger. Northriver used to cut a full week of one hinge size because changeover took 45 minutes — which is a changeover and scheduling problem, not a reason to build a week of stock.
Overprocessing
Doing more work than the customer or the specification requires: an extra polish that is immediately painted over, collecting data nobody uses, or a signature loop that adds no new review. Ask, “Would the customer notice if we stopped?” and “Does this step change a CTQ?” If both answers are no, you are a candidate for overprocessing.
Defects
Scrap, rework, returns, and incorrect information. Defects consume capacity twice (or more) and delay the good unit the customer actually ordered. The packing Pareto above is a defect-waste picture: pin off-center and finish scratches dominated the month. Downstream, defects also create waiting and extra motion. Related tools include FMEA, poka-yoke, and fishbone diagrams.
Skills (unused talent)
The eighth waste is not using the knowledge of the people closest to the work: no way to raise a problem, no time to test an idea, or a standard written only by people who do not run the process. A suggestion box that is never reviewed is Skills waste. So is training that is never allowed to be used.
How to see waste in a real process
Walk the path of the work, not the path of the meeting. For a physical product, follow one unit from request to delivery and time the delays. For a service or office process, follow one request through the system, including inboxes. A current-state value stream map makes the wait-versus-touch-time gap hard to argue with. A waste walk with a TIMWOODS checklist is faster and is a good Yellow Belt skill.
When you log wastes, write a fact, not a slogan: “operator walks 40 feet for pins, 12 times per hour,” not “bad layout.” Facts are what you improve.
How this shows up on belt exams
Expect questions that give a short scenario and ask which waste it is, or that ask which waste tends to drive the others (often overproduction). Know both the seven-waste list and TIMWOODS. You may also be asked to classify a step as value-added or non-value-added. Related pages: 5S, value stream mapping, JIT, and the Body of Knowledge hub.
Frequently asked questions
Are there seven wastes or eight?
The classic Toyota list has seven: transportation, inventory, motion, waiting, overproduction, overprocessing, and defects. Many Lean Six Sigma programs add an eighth waste — unused skills or unused human talent — and teach the acronym TIMWOODS (or TIM WOODS). Use the list your exam body prints in its glossary, and be ready to recognize both.
Is all inventory waste?
Inventory above what is needed to protect a true constraint or to serve the customer now is waste. A small, designed buffer in front of a bottleneck can be a deliberate decision. A week of “just in case” finished goods that exist because changeovers are long is waste you can attack by reducing changeover time, not by buying more shelves.
What is the difference between motion and transportation?
Motion is about people (or a machine’s empty movement). Transportation is about moving the product or information from place to place. Walking to a tool is motion; forklifting a pallet to another building is transportation. Both can appear in the same messy layout.
Related guides
Last updated: · Published by Lean Six Sigma Training Guide (sixsigmatrainingfree.com) · How this guide is written